PLD52MU
OWNER'S MANUAL
Mobile Video System
Motorized Slide Down Panel
2.5 Inch TFT Color Monitor
Car DVD/VCD/CD/MP3 Player
AM/FM Digital Pll Tuning Radio
MPEG4 Player
USB Connect
Remote Control
SAFETY INFORMATION
CAUTION:
THIS DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS DVD
PLAYER USES A VISIBLE/INVISIBLE LASER BEAM WHICH COULD CAUSE .
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE DVD PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. Patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners.Use of this
copyright protection technology must be authorized by Macro vision Corporation,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
REGION MANAGEMENT INFORMATION:
This DVD Player is designed and manufactured to respond to the Region
Management Information that is recorded on a DVD disc. If the Region number
described on the DVD disc does not correspond to the Region number of this
DVD Player, this DVD Player cannot play this disc.
2
DISC NOTES
unusable) depending on your handle it
and conditions in the usage environment.
Note these scratches are not an
Disc formats supported by this
player
DVD
12 cm disc
V I D E O
indication of any problem with the player.
Label side
up
(Single-sided disc only)
Video CD
12 cm disc
CD
Do not touch
the
underside
of the disc
12 cm disc
MP3
12 cm disc
MP3
CD-RW
Do not
bend
Discs which cannot be played
with this player
DVD-ROM
DVD-R/DVD-RAM
CDV
Wipe the disc from
center
toward the outside
edge
CD-G
Handling and Cleaning
Dirt, dust, scratches and warping disc
will cause misoperation.
Do not place stickers or make
scratches on discs.
Preparing New Discs with Rough
Spots
A new disc may have rough edges on
its inside and outside edges.If a disc
with rough edges is used, the proper
setting will not be performed and the
player will not play the disc.Therefore,
remove the rough edges in advance
by using a ball point pen or pencil as
shown on the right.To remove the
rough edges, press the side of the pen
or pencil against the inside and outside
edges of the disc.
Do not warp discs.
A disc should always be kept in its
case when not in use to prevent from
damaging.
Do not place discs in the following
places:
1.Direct sunlight
2.Dirty, dusty and damp areas
3.Near car heaters
4.On the seats or dashboard
Rough spots
on
outside edge
Disc Cleaning
Use a dry soft cloth to wipe the surface.
If the disc is quite dirty, use a soft cloth
slightly moistured with isopropyl (rubbing)
alcohol. Never use solvents such as
benzine, thinner or conventional record
cleaners as they may mar the surface of
the disc.
Ball point pen
or pencil
Rough spots
on inside
edge
Note:
A disc may become somewhat scratched
(although not enough to make it
3
INSTALLATION
NOTES:
Choose the mounting location where the unit will not interfere with the normal
driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure
it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use
of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or
other modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the
passenger if there is a sudden stop, like an emergency stop.
If installation angle exceeds 30 from horizontal, the unit might not give its
optimum performance.
30
Avoid installing the unit where it would be subject to high temperature, such
as from direct sunlight, or from hot air, from the heater, or where it would be
subject to dust, dirt or excessive vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either from "Front"(conventional DIN
Front-mount) or "Rear"(DIN Rear-mount installation, utilizing threaded
screw holes at the sides of the unit chassis). For details, refer to the following
illustrated installation methods.
4
INSTALLATION
DASH BOARD
HEX NUT
METAL MOUNTING
STRAP
SPRING WASHER
PLAIN WASHER
TAPPING SCREW
CONSOLE
SLIDE BRACKET
HOUSING
HEX BOLT
KEY PLATE
PLASTIC COVER
KEY PLATE
If you want to take CHASSIS out of the SLIDE BRACKET HOUSING,
first remove the PLASTIC COVER of the both sides away, then insert
the two KEY PLATE into left and right side of chassis as above illustration.
5
CHAGNE ANGLE
CHANGING THE CONTROL PANEL ANGLE
When you want to change the angle to play, you can press repeatedly the
(angle)button to select the desired angle as follows:
Angle 1
Angle 2
Angle 4
Angle 3
Caution:
Do not insert your finger behind the control panel
6
ELECTRIC CONNECTION
WIRING CONNECTION
MAIN UNIT
(B+)12V
REAR CAMERA SWITCH
WHITE
GREEN
(B-)PARKING BRAKE
YELLOW
REAR CAMERA INPUT
AUX(optional)
VIDEO IN YELLOW
RCH IN RED
ANTENNA CONNECTOR
IGNITION RED
SWITCH(B+)
LCH IN WHITE
RCA CABLE
GREY SUBWOOFER
VIDEO OUT 2 YELLOW
COAXIAL OUT BROWN
RCH RED
REAR RCA OUTPUT
CABLE (optional)
CHOKE
BOX
MEMORY
BACK-UP(B+)
YELLOW
BLACK
LCH WHITE
FRONT RCA OUTPUT
CABLE
FRONT RCA RED
VIDEO OUT 1 YELLOW
FRONT RCA WHITE
R
GROUND(B-)
L
(FOR RCA LINE OUT VERSION ONLY)
FUSE
AUTO
ANTENNA
BLUE
GREY
WHITE
FRONT
FRONT
Rch SPK.
Lch SPK.
WHITE/BLACK
GREY/BLACK
VIOLET
REAR
GREEN
REAR
Rch SPK.
Lch SPK.
GREEN/BLACK
VIOLET/BLACK
7
REMOTE CONTROL
15
16
5
3
17
7
19
2
20
21
1
13
6
23
14
22
18
9
12
25
24
11
10
4
8
Press it to change the display to clock display.
Press it to change between RADIO ,DISC and AUX IN mode.
Press it to stop playback.
1. CLK
2. MODE
3. STOP
4. SETUP
5. MO/ST(AUDIO)
Display the SETUP menu.
In radio mode, press it to select STEREO or MONO mode (In disc
mode, press it to changing of the AUDIO soundtrack on multi-
audio soundtrack DVD disc. Changing of the sound mode of the
VCD/CD disc)
Changing of the SUBTITLE language on multi-subtitle language
DVD disc. In radio mode,.Press this button for distance reception
when you are located at weak signal location, depress it for
stronger signal.
6. SUBTITLE
LO/DX
Switch the Repeat mode of DVD/VCD/CD/MP3 disc.
Disc search button, cooperatively used with numeric buttons
7. REPEAT
8. GOTO
Press to skip to the next track & press
(Note: In DVD mode, press continually the
to skip back one track.
twice to skip back one)
9.
/
Press it repeatedly to change mode through volume , bass, treble,
balance, fader, color, bright, contrast and tint modes.
Press it to adjust volume level
10. SEL
11. VOL+/VOL-
12.
In case of the SETUP MENU mode,
/
/
/
buttons served as
/
/
/
cursor buttons to select item left/right,ahead/back.
Press it to display the root menu of the DVD disc. Press and hold
for more than 2 seconds can have SUBWOOFER, press it again
for more than 2 seconds to release this mode.
Display statistical disc information during playback (To change
the band in radio stations)
13.MENU
SUB WOOFER
14.BAND(OSD)
Press it to turn on the unit ,press it again to turn off.
Press once to pause a play, press again to resume playback.
Press it to mute down sound.
15.POWER
16.PLAY/PAUSE
17.MUTE
Display the TITLE menu that is stored in DVD disc changing
between PBC ON and PBC OFF on the VCD disc.(Auto store
and preset scan function in radio stations .)
18.TITLE/PBC
(A/P)
Press it to change the view angle.
Changing of the view angle on multi-angle DVD disc.
Press it to turn to equalization function.
19.
20.ANGLE
21.EQ
Press
to start forward rapidly &
to reverse rapidly.
22.
23.ENTER
/
Confirm the Track/Chapter selected with the number key or
selected with the cursor buttons on TV screen.
Numeric buttons.
24. 0 - 9
25.+10
Tens digit select button, cooperatively used with numeric buttons .
8
REMOTE CONTROL
Preparing the Remote Control
Inserting the Batteries
1.First push to inside as the direction indicated by the arrow (See )And then
1
Remove the battery holder as the direction indicated by the arrow (See ).
2
2.Replace the battery Set a new battery property with (+)side up as illustrated
(See ).
3
3.Insert the battery holder. Push in the holder to the original position(See 4 ).
Using the Remote Control
Face the remote control towards the player front face IR mark (remote control signal
receiver).
Operation angle: About 30 degree in each the direction of the front of the IR mark.
To prevent damage to the unit, be sure to follow the connection diagram
(page 7).
9
BASIC OPERATION
14 19 12 13 21
17
4
6
7
8
23
S E L
18
1
5
16 15 20 3 2 22 11 10
9
24
25
1.PWR BUTTON
Press it to turn on the unit. Press it again to turn off.
2-3.VOL+/VOL- & SEL BUTTON
Press sel button repeatedly to change mode through volume, bass, treble,
balance, fader, color, bright, contrast and tint modes. Face up or down swing the
SEL knob VOL + /VOL- to adjust the selected mode.
(The corresponding value will show on the display.)
When mode has not been adjusted for several seconds, display returns to normal
radio or CD display.
Volume
Bass
Treble
Balance
Fader
Tint Contrast
Bright
Color
A.Volume:Adjust volume level by using VOL + / VOL - button.
Note: The unit is initially set to volume mode.
B.Bass:Press SEL button one time. Adjust bass level by using VOL + / VOL -
button.
C.Treble:Press SEL button two times. Adjust treble level by using VOL + / VOL -
button.
D.Balance:Press SEL button three times. Adjust sound balance between left
and right speakers by using VOL + / VOL - button.
E.Fader:Press SEL button four times. Adjust sound balance between front and
rear speakers by using VOL + / VOL - button.
(NOTE: the function of the Color, Bright, Contrast and Tint. Please see 14 page.)
4.BAND BUTTON
In RADIO mode, press the BAND button on the front panel or on the remote
controller to select your desired radio band and word which band is selected
will be displayed on LCD. Press it to change the bands as below :
FM
MW
LW
FM
MW
FM
AM
For 3 Bands (Europe)
For 2 Bands (Europe)
For 2 Bands (USA)
5.EQ BUTTON
Press it to turn to equalization function and to select desired audio mode.
There are four kinds of mode as below:
JAZZ
CLAS
POP
10
ROCK
BASIC OPERATION
6-7-8-9-10-11.PRESET STATION
A.To memorize the current frequency, press any one of the six preset buttons[1-6]
on the front panel or on the remote controller hold for more than 2 seconds.
B. To recall the preset memory, press one of the preset buttons [1-6].
C.Press 1/TOP(6) button to select the first track/chapter to play.
a.In the state of VCD/CD/MP3 disc playing, press the button on the front panel
to select the first track/chapter to play.(depend on the disc used for VCD)
b.In the state of DVD disc playing, the 1TOP button is not available.
D.Long Press 2/RPT(7) button to select repeat mode as follow.
CHAPTER REPEAT ON
REPEAT OFF
REP-ALL
TITLE REPEAT ON
DVD:
REP-ONE
VCD/CD:
a.Continuously repeat at the current chapter/track, when selected
REP-ONE mode.
b.Select REP-ALL mode to continuously repeat all chapter/track on the
current disc.
c.REPEAT feature does not support VCD2.0 (with PBC ON).
E. Long Press 3/INT(8) button to scan disc.
a.In the state of CD disc playing,press the 3/INT button to play the previous 6
seconds part of each track/chapter on disc.
b.In the state of MP3 disc playing, the 3/INT button is not available.
c.In the state of VCD disc playing , long press the 3/INT button, the screen will
display as follow (long press it again will release this mode.):
SELECT DIGEST TYPE:
TRACK DIGEST
DISC INTERVAL
TRACK INTERVAL
/
and then press the ENTER button to confirm .
/
/
1). You can use the
buttons on the remote control to select the item,
2). In Track Digest OR Disc/Track Interval MODE.
/
/
/
You can use the
ENTER to confirm .
buttons to select the items ,and then press the
You can also select the items using the corresponding number buttons, and
then press the ENTER to confirm .
d.In the state of DVD disc playing , long press the 3/INT button, the screen will
display as follow (long press it again will release this mode.):
SELECT DIGEST TYPE:
TITLE DIGEST
CHAPTER DIGEST
TITLE INTERVAL
CHAPTER INTERVAL
/
/
/
and then press the ENTER button to confirm .
1). you can use the
buttons on the remote control to select the item,
2). In Title/Chapter Digest OR Title/Chapter Interval MODE.
/
/
/
You can use the
to confirm .
buttons to select the items ,and then press the ENTER
You can also select the items using the corresponding number buttons, and
then press the ENTER to confirm .
11
BASIC OPERATION
F. Long Press 4/RDM (9)to play disc in random.
In the DVD/VCD/CD/MP3 disc playing, press the 4/RDM button on the front
panel to play in random (depend on the disc used for VCD).
12.AS/PS BUTTON
When shortly pressing the APS button on the front panel or the A/P button on the
remote controller, the radio searches for each preset station. When the field
strength level is more than the threshold level of stop level, the radio is holding at
that preset number for few seconds with releasing mute, and then searches again.
In FM band, FM 1,FM 2 and FM 3 is checked one at a time When long pressing the
APS or A/P button (more than 1 second), the radio searches from the current
frequency and checks the signal strength level until 1 cycle search is finished.
And then 6 strongest stations are preset to the corresponding preset number.
The AS operation is implemented in the each band of selected band. When the
AS operation is finished, the radio executes the preset scan.
13.MU BUTTON
Press it to mute down sound. Press it again to release this mode and recover
previous volume level.
14. (ANGLE)BUTTON
Press it to change the view angle,you can adjust the angle for your desired
15.CLK BUTTON
Press it to change the display to clock display. Press it again to return to previous
display. In clock display, press and hold for about 2 seconds until the hour display
flashes. Face up or down swing the SEL Knob VOL+/- to adjust hours ,press CLK
button to flash minute then use VOL+ /VOL- to adjust minutes.
16.
BUTTON
Pressing
press
during playback will stop play temporary. Return to normal playback,
once again.
17.
/
A.When face right or left swing the SEL knob
BUTTONS
/
button (more than 2 seconds )
during play. The speed of rapid forward/reverse changes according to the disc
as follow.
DVD/VCD/CD/MP3:
Normal Playback 2x
4x
8x
16x
B.Face right or left swing the SEL knob the
to next track or back one track.(Note: In DVD mode , face left swing continually
the SEL knob the button twice during playback to skip back one track.)
/
button during playback to skip
Note: For some VCD 2.0 dics (PBC-playback control),
be unavailable.
and
buttons may
C.Press UP or DN button on the remote controller or face left or right swing the
SEL knob on the front panel to manually tune up or down for your desired
/
station. Press them hold for more than 2 seconds to automatically tune up or
down for the stronger station.
12
BASIC OPERATION
18.MOD BUTTON
Press it repeatedly select AUX IN , RADIO and DISC mode. In USB during
playback , you can press STOP button and then press the GOTO button to
select the DISC mode.
19.EJECT BUTTON
Press the eject button to turn downward the front panel and eject the disc from
the disc compartment. Also you can insert the disc to the compartment.
20.ST BUTTON
Press ST button to select STEREO or MONO reception for radio stations.
21.MENU BUTTON
Press it to display the root menu of the DVD/VCD(Only when PBC not in use) disc.
22.RESET BUTTON
RESET button is placed on the housing and must be activated with either a
ballpoint pen or thin metal object. The RESET button is to be activated for the
following reasons:
A. Initial installation of the unit when all wiring is completed.
B. All the function buttons do not operate.
C. Error symbol on the display.
Note:If press RESET button , the unit can't work yet, please use a cotton swab
soaked in isopropyl alcohol to clean the socket on the back of the front panel.
MP3/WMA/JPEG DISC PLAY
1.When inserting an MP3/WMA/JPEG disc
Ex: When Mp3 file is detected.
4
5
6
1 .Current track(file)(highlighted bar)
.Current track (file) number/total
number of tracks(files) in the current
folder.
2
00:56
04:07
3
2
Repeat one
003/112
.Elapsed playing time of the current
track(not available for JPEG disc)
.total playing time.( not available for
JPEG disc)
3
4
Mp3
K
P
Mp3
Mp3
1
woman 1
ton
.Selected playback mode
.Operation mode icon.
5
6
..........n..e.w.
(Play),
(stop), (pause), (forward)
(reverse).
In stop mode , use
/
/
/
then press ENTER button to confirm.
on the remote control to select the item or folder,
Pressing REPEAT button repeatedly can select two kinds of repeat play mode.
2. REP-ONE:
Play the same song over and over again.
3. REP ALL:
Play all songs in the discover and over again.
In the playback, use
In the playback, face right or left swing the SEL knob
seconds ) on the front panel or short press
forward/reverse.
or
to skip an item ahead or back.
button (more than2
on the remote control to rapid
/
/
13
BASIC OPERATION
AUX INPUT JACK
When the unit connect external A/V (See number 23), you can press MODE to
switch the AUX input mode.
TFT MONITOR OPERATION
1. Press the SEL button(3) repeatedly during DVD/VCD mode to display the adjustment
items on the screen(24). and then face up or down swing the VOL+/- buttons to adjust
the selected item.
(The corresponding value will show on the display.)
Volume
Bass
Treble
Balance
Fader
Tint Contrast
Bright
Color
2.ADJUSTABLE ITEMS:
COLOR: 0 to 32
Adjust the color fo the picture-lighter or darker.
BRIGHT: 0 to 32
Adjust if the picture is too bright or too dark.
CONTRAST: 0 to 32
Adjust the contrast of the bright ans dark portion.
TINT: 0 to 32
Adjust the tint if the human skin color is unnatural.
-Adjustable when “NTSC “ is selected for “NTSC/PAL “ .
(The function of the VOLUME, BASS,TREBLE, BALANCE and FADER, Please
see page 10.)
REAR VIEW CAMERA
When connecting the rear view camera.the mirror image of the rear view through
the rear view camera is automatically displayed on the monitor when you change
the gear to the back position.(The monitor on the unit only.)
NOTE(for the brake function)
if the parking brake is not engaged,“parking brake” flashes on the monitor,
and no playback picture will be shown.only the audio will be heard.
-This warning appears only when the parking brake wire is connected to the parking
brake system built in the car. (See page .7)
14
BASIC OPERATION
USB Operation
On-screen Display Function
Press the OSD button during playback
to display the contents of the current
disc on the screen.
A.Example for DVD:
a.Press OSD for the first time:
A.Plug the USB connect line to the USB
socket (see number 25) of the unit
properly,(See fig.1) when the USB
appliance connect to the USB port of
the connect line, the system star
playing track of the USB appliance
automatically.
TITLE ELAPSED
TT 01/01 CH 01/38
0:02:06
B. IN USB playing , you can press the
cursor button to select the item.Then
press ENTER button to playing.
also press numeric to play the
Title Number, Total Title Number,
Chapter Number, Total Chapter
Number of this Title of the disc
currently being played will be shown
on the screen,along with the elapsed
time.
corresponding track directly. Press
the
track or skip to the back one track
Press the button to fast forward
or fast reverse.
/
button to skip to the next
b.Press OSD for the second time:
/
TITLE REMAIN
TT 01/01 CH 01/38 3:24:36
Press the REPEAT button to select
repeat play mode.
You can press the EJECT button to
eject the disc or insert the disc into
the compartment.
When insert the disc, the unit will
play the disc automatically .
C.In USB mode(when the disc in the unit)
Press the STOP button once , and
then press the GOTO button, the unit
will change the DISC mode to play,
In DVD/VCD/CD mode,
c.Press OSD for the third time:
CHAPTER ELAPSED
TT 01/01 CH 01/38 0:02:56
d.Press OSD for the fourth time:
CHAPTER REMAIN
TT 01/01 CH 01/38 0:04:32
e.Press OSD for the fifth time:
The message on the screen will be
cleared.
Press the STOP button twice, and
then press the GOTO button, the unit
will change the USB mode to play
In MP3 mode,
B.Example for VCD/SVCD/CD:
a.Press OSD for the first time:
press the STOP button once, and
then press the GOTO button, the unit
will change the USB mode to play.
Note:
SINGLE ELAPSED
TRACK 01/16
00:49
a:To prevent damage to the USB ,
during the playback don`t pull out.
b.Press OSD for the second time:
SINGLE REMAIN
b:In the state of the DISC playing ,
Best to pull out the USB.
TRACK 01/16
02:45
c.Press OSD for the third time:
TOTAL ELAPSED
TRACK 01/16
00:60
USB port
d.Press OSD for the fourth time:
(USB connect line)
TOTAL REMAIN
TRACK 01/16
78:46
(Fig.1)
15
BASIC OPERATION
e.Press OSD for the fifth time:
The message on the screen will be
cleared for SVCD and VCD.
C.Example for MP3:
Each time OSD is pressed, the
message displayed on screen changes
as follows:
Notes:The language number is
different according to the disc.Some
discs only contain one subtitle
language.When no different subtitle
language are recorded, will be
displayed at screen left top corner.
SINGLE ELAPSED
SINGLE REMAIN
MULTI-ANGLE FUNCTION(For
DVD only)
Press ANGLE during playback.Each
time the button is pressed, number
of the angle changes in sequential
order.
Notes:The angle number is different
according to the disc.The function
only work for disc having scenes
recorded at different angles.When
no different angle are recorded, will
be displayed at screen left top corner.
MULTI-AUDIO LANGUAGE
FUNCTION
A.DVD:Press AUDIO during playback.
Each time the button is pressed,
number of the audio soundtrack
language changes on sequential
order.
NOTES:The language number is
different according to the disc.Some
disc only contain one language
soundtrack.When no different
language soundtrack are recorded
will be display at screen left top
corner.
MPEG4 DISC PLAY
MPEG4 disc is playing as the format
of FILE . For example:
00:56
04:07
Repeat one
B.VCD/CD:
Press AUDIO during playback.
It is possible to switch the sound
between monaural and stereo sound.
001/001
MAY-AUG
C14-Long-fright
MONO LEFT
MONO RIGHT
STEREO
MIX-MONO
..............
TITLE MENU FUNCTION
A.DVD:If the DVD has multiple titles
recorded on the disc. It can select
preferred title from the title menu
to start playback.
a.Press TITLE during playback.
The title menu is display.
b.Press the cursor button shown
in TV screen, select preferred title
by the cursor button and confirmed
by ENTER key.
In stop mode ,Use
/
/
/
on the
remote control to select the item or
folder, then press ENTER button to
confirm .Pressing REPEAT button
repeatedly can select three kinds of
repeat play mode.
REP-ONE:
Play the same file over and over again.
REPEAT-ALL:
Play all files in the current directory
in sequence, over and over again.
DISC REPEAT:
B.VCD:Press TITLE/PBC button on
theremote controller while the disc
is playing, you can switch between
"PBC on"and "PBC off"mode.
Play all files in the discover and over
again. In the playback, use
skip an item ahead or back.
or
to
MULTI-SUBTITLE LANGUAGE
FUNCTION (For DVD only)
Press SUBTITLE during playback.
Each time the button is pressed, number
of the subtitle language changes in
sequential order.
When face the right or left swing and
hold the SEL knob the for more
than 2 seconds on the front panel or
short press the on the remote
control to rapid forward /reverse.
/
/
16
SETUP
GENERAL SETUP
--- GENERAL PAGE ---
DOLBY
DOLBY
-----General setup page----
-----General setup page----
TV Display
Normal/PS
Normal/LB
Wide
TV Display
LB
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
Spdif Output
Captions
ENG
SPDIF/RAW
ON
Screen Saver
Last Memory
Screen Saver
Last Memory
ON
ON
Set TV Display Mode
Go To General Setup Page
TV Screen
Video
Material
1. Press SETUP button on the remote
control .
Wide(16:9)
Pan Scan
Normal
Letter-box
4:3
2.The SETUP menu is displayed.
3.Select the preferred item by using the
/
/
/
buttons
4.Press ENTER button.
a.GENERAL SETUP
1.TV DISPLAY SETUP
This setup page includes the item
of TV display & audio output feature.
The detail please refer to
This is to select the appropriate TV
aspect (4:3 or 16:9) according to the
connected TV set.
GENERAL SETUP MENU.
b.SPEAKER SETUP
Normal/PS (For 4:3 TV)
Played back in the PAN & SCAN style.
(If connected to wide-screen TV, the
left and right edges are cut off.)
Normal/LB (For 4:3 TV)
This is to activate the audio output
from DOLBY AC3 5.1 DOWNMIX
to 2 channel mode. Please refer to
SPEAKER SETUP MENU.
c.DOLBY DIGITAL SETUP
Please refer to DOLBY DIGITAL
SETUP.
Played back in letterbox style.
(If connected to wide-screen TV, black
bands appear at top and bottom of the
screen.)
d.PREFERENCE SETUP
This setup page includes all the
configuration of support feature.
The detail please refer to
Wide (For 16:9 TV)
Select when a wide-screen TV set is
connected.
PREFERENCES SETUP MENU.
17
SETUP
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
ON
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
Osd Lang
OFF
SPDIF OFF
SPDIF/RAW
SPDIF/PCM
Spdif Output
Captions
Screen Saver
Last Memory
Set Angle Mark
Screen Saver
Last Memory
Setup SPDIF
2.ANGLE MARK DISPLAY SETUP
If it is set to ON, when the multi-angle
4.SPDIF OUTPUT
This is to activate the audio output
from SPDIF OFF mode to SPDIF/RAW
mode to SPDIF/PCM mode.
DVD disc is playing,
(the angle
mark) will appears on the screen; if is
set to OFF, the mark will not appear.
DOLBY
DOLBY
-----General setup page----
TV Display
-----General setup page----
TV Display
English
French
Angle Mark
OSD Lang
Spdif Output
Captions
Angle Mark
OSD Lang
German
Spanish
Italian
ON
Spdif Output
OFF
Captions
Screen Saver
Last Memory
Screen Saver
Last Memory
Closed Caption
Portuguese
Set OSD Language
5.CAPTIONS SETUP
3.OSD LANG TYPE SETUP
Select the preferred OSD language
Activate the CAPTIONS feature by
selecting ON. And release this feat-
ure by selecting OFF.
by using the
/
buttons.
18
SETUP
SPEAKER SETUP
--- SPEAKER SETUP PAGE ---
DOLBY
DOLBY
-----General setup page----
TV Display
-----Speaker Setup Page----
Angle Mark
OSDLang
Spdif Output
Captions
DOWNMIX
LT/RT
STEREO
ON
Screen Saver
Last Memory
Screen Saver
OFF
Set Downmix Mode
This is to activate the audio output from
DOLBYAC3 5.1 DOWNMIX to 2 channel
mode. Select the preferred SPEAKER
connection by using the cursor buttons.
Select the LT/RT to activate the Dolby
surround compatible output.
6.SCR SAVER SETUP
Select the SCR SAVER output
ON/OFF.
Select the STEREO to activate simple
stereo mode.
DOLBY
DOLBY DIGITAL SETUP
DOLBY
-----General setup page----
TV Display
-----Dolby Digital Setup----
Angle Mark
OSD Lang
Spdif Output
Captions
FULL
6/8
DYNAMIC
4/8
2/8
ON
Screen Saver
OFF
OFF
Last Memory
Set Last Memory State
Set DRC OFF
DYNAMIC RANGE CONTROL
Select DRC and adjust the dynamic
range of a Doby Digital encoded
7.LAST MEMORY SETUP
Select the LAST MEMORY output
ON/OFF.
program. There are 8 steps between
full compression and off compression.
19
SETUP
PREFERENCES SETUP
--- PREFERENCES PAGE ---
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
PAL
TV Type
English
French
Spanish
German
AUTO
NTSC
Audio
Audio
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
Disc Menu
Parental
Password
Default
Italian
Portuguese
OFF
Set TV standard
Preferred Subtitle Language
1.TV TYPE SETUP
3.SUBTITLE LANGUAGE SETUP
Select the preferred SUBTITLE
language by using the cursor buttons.
This player can play discs recorded
in either PAL or NTSC format.Select
NTSC format, when you connected to
NTSC TV.Select PAL format, when
you connected to PAL TV.Select AUTO
format, the player TV output format
will according to the DVD disc format..
DOLBY
DOLBY
-----Preference Page----
TV Type
-----Preference Page----
TV Type
Audio
English
English
Audio
French
Subtitle
French
Disc Menu
Parental
Password
Default
Spanish
German
Italian
Subtitle
Spanish
Disc Menu
German
Parental
Italian
Portuguese
Password
Portuguese
Default
Preferred Menu Language
Preferred Audio Language
4.DISC MENU LANGUAGE SETUP
Select the preferred DISC MENU
language by using the cursor
buttons.
2.AUDIO LANGUAGE SETUP
Select the preferred AUDIO sound-
track by using the cursor buttons.
20
SETUP
DOLBY
DOLBY
-----Preference Page----
-----Preference Page----
TV Type
1KID SAF
2G
TV Type
Audio
Audio
3PG
Subtitle
Disc Menu
Parental
Password
Default
Subtitle
4PG13
5PGR
6R
Disc Menu
Parental
Password
Default
7NC 17
8 ADULT
OFF
RESET
Load Fcatory Setting
Set Parental Control
7.DEFAULTS
Select reset to become factory initial
setting.
5.PARENTAL
Select suitable parental guidance by
the cursor buttons and conformed by
pressing ENTER button.
DEFAULTS TABLE
DOLBY
TV DISPLAY
NORMAL/LB
ON
-----Preference Page----
TV Type
ANGLE MARK
OSD LANGUAGE
ENGLISH
SPDIF/RAM
ON
GENERAL SETUP
Audio
SPDIF OUPUT
CAPTIONS
Subtitle
Disc Menu
Parental
SCR SAVER
ON
LAST MEMORY
ON
DOWNMIX
SPEAKER SETUP
DOLBY DIGITAL
STEREO
OFF
Password
Default
CHANGE
DYNAMIC
TV TYPE
AUDIO
AUTO
ENGLISH
OFF
Change Password
SUBTITLE
6.PASSWORD
DISC MENU
Select the change and press ENTER
button. Type the old password (The
initial factory code is 1379) and key
in 4 characters password now you
want to use, and retype again to
confirm key in correctly.
PREFERENCES
ENGLISH
8 ADULT
1379
PARENTAL
PASSWORD
21
SPECIFICATION
GENERAL
Supply Voltage
Current Consumption
SIGNAL SYSTEM
: 12v Dc (11v-15v)
: More Then 10 A
: Compositive Video 1.0vp-p 75
DISCS PLAYED
(1) Dvd-video Disc
5"(12 Cm) Single-sided, Single-layer
5"(12 Cm) Single-sided, Double-layer
(2) Compact Disc (cd-da, Video Cd)
5"(12cm) Disc
AUDIO SIGNAL OUTPUT
CHARACTERISTICS
: 2ch&4ch Line Out
(1) Frequency Response 20 Hz - 20 Khz
(2) S/n Ratio
90 Db (jis)
(3) Wow And Flutter
Below Measurable Limits
RADIO
FM TUNER SECTION
Tuning Range
: 87.5-107.9MHz
: 10.7MHz
IF Range
Usable sensitivity(30dB)
AM TUNER SECTION
Frequency Range
IF Range
: 15dB
: 530-1710KHz
: 450KHz
Usable sensitivity(30dB)
: 45dB
TFT MONITOR
Monitor Screen Size
Number of Pixels
Color System
: 2.5 Inch Wide
: 480 X 234 pixes
: NTSC/PAL
NOTE:
Specifications and design are subject to modification, without notice, due to
improvements in technology.
22
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
SYMPTOM
CAUSE
SOLUTION
If the power supply is properly
connected to the car accessory
terminal,switch the ignition key
to "ACC"
The car ignition switch is
not on
No power
The fuse is blown
Replace the fuse
Presence of disc inside the Remove the disc in the player,
player.
then put a new one
Inserting the disc in reverse Insert the compact disc with
direction
Disc can not be
loaded or ejected
the label facing upward
Clean the disc or try to play a
new one
The disc is extremely dirty
or defective
Temperature inside the car
is too high
Cool off or until the ambient
temperature return to normal
The color system is
set incorrectly
Television/video
imageappears
black-white
Please switch to correct color
system from menu
Make proper connection
The unit is not connected
to the parking brake
detection switch
No television/video
image appears
according to“wire connection”
For safety reasons no television
/video images are displayed while
the vehicle is moving.
The parking brake is not
engaged
Engaging the parking brake will
cause images to be displayed.
Please the television mode of
the choice accommodation
The disc format is not
accordingto the TV-set
used (PAL/NTSC)
No color in picture
No JPEG files are recorded
on the disc.
JPEG disc can
not be played
back
Change the disc
Change the disc
Record JPEG files using a
compliant application
JPEG files are not recorded
in a compliant formant
The built-in microcomputer Press the RESET button.
is not operating properly
due to noise
The operation keys
do not work
Front panel is not properly fixed
into its place
The antenna cable is not
connected
The radio does not
work
Insert the antenna cable firmly
The signals are too weak
Select a station manually
888-J3001-15
23
|